background image

Getting started FLUOVIEW/

Outline of LSM Observation Procedures

1-20

Page

(2) Make sure that the output control is set to the maximum position.

(3) Warm up for about 30 minutes until the oscillation stabilizes.

(4) Open the shutter lever of the laser tube.

2.5.  For the method of turning an IR (750 nm) laser on, refer to the

instruction manual of the IR laser (by MELLESGRIOT).

 2.6.  HeCd laser.

(1) Turn the rocker switch(1) of laser controller to “I” (ON).

(2) Turn the key switch(2) of laser controller to the ON position.

(3) Turn the key switch(3) of remote interface module to the ON

position.

(4) Turn the <ON> button of the remote interface module ON.

After the key is set to ON, it takes tens of seconds before the

laser oscillation starts.

To stabilize the laser beam output, we

recommend leaving the system for warm-up

after turning the laser power ON. The warm-

up period should exceed 10 minutes when

the laser system in use uses an Ar laser or

exceed 30 minutes when it uses a Kr laser,

Green HeNe laser or HeCd laser.

3. Turning the reflected light power supply unit

    (1) Set the power switch to ON.

Once the reflected light power supply unit is

turned OFF, do not turn it ON again for at

least 10 minutes. Otherwise the service life

of the mercury burner will be shortened.

Laser controller

Remote interface module

NOTE

(1)

(1)

(2)

(3)

(4)

Summary of Contents for FLUOVIEW FV500























































































































































































































































































































































































































































































Reviews: