Oce CPS900 User Manual Download Page 86

Page: 86 / 138

Chapter 3 Print Jobs on the Océ CPS900®

How to stop a job

Stop while the operator defines the settings for a job

[37]

Note:

Remember the following: When the operator uses set-build, the Correction

key (

) has a different function. Press one time, the number of prints is set to 1.

Press two times, all the settings are set to the default value of the template. Each next
time the Correction key (

) is pressed, the last subset is deleted.

[37] Stop behavior while the operator defines the settings for a job

If the Correction key (

) is

pressed ...

Then ...

one time

the number of prints is set to 1

two times

all the settings are set to the default value of the
template

three times

the operator panel returns to the main screen
with the standard templates

Summary of Contents for CPS900











































































































































Search results

Summary of Contents for CPS900

Reviews:

Related manuals for CPS900

Brands by name

Popular brands

Oce CPS900, User Manual

Search results

Summary of Contents for CPS900

Reviews:

Related manuals for CPS900

Brands by name

Popular brands