Oce CPS900 User Manual Download Page 30 | Manualshive

Page: 30 / 138

background image

30

Chapter 1 Introduction

The Operator Attention Light (optional)

The Operator Attention Light (optional)

Introduction

The operator panel informs the operator when the system needs operator interaction.
However in most cases the operator takes care of more than one machine.
The operator attention light is used to indicate the state of the system when the
operator is not close to the system.

[6]

[6] The Operator Attention Light

The system can be in different states (statuses). The table below shows the possible
states in which the system needs operator interaction.

«
...
28
29
30
31
32
...
»

Summary of Contents for CPS900











































































































































Reviews:

No comments

Related manuals for CPS900

Pixma MG2400 Series

Brand: Canon Pages: 2

Brand: Oki Pages: 4

SCX 4500W - Personal Wireless Laser Multi-Function...

Brand: Samsung Pages: 113

imageRUNNER ADVANCE 8105

Brand: Canon Pages: 5

imageCLASS MF269dw

Brand: Canon Pages: 32

Brand: Samsung Pages: 158

Brand: Parkside Pages: 176

ProJet x60 Series

Brand: 3D Systems Pages: 72

4250 - WorkCentre - Copier

Brand: Xerox Pages: 4

Brand: Oki Pages: 2

Brand: FujiFilm Pages: 28

Brand: Triumph Adler Pages: 202

Brand: Lanier Pages: 4

ColourLaser 21 Series

Brand: Xante Pages: 32

Brand: Skynet Pages: 18

Brand: Oki Pages: 76

LabeLase 1000Exhaust

Brand: InfoSight Pages: 38

RIP Station 5100

Brand: Epson Pages: 140

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands