Oce CPS900 User Manual Download Page 72

Page: 72 / 138

Chapter 3 Print Jobs on the Océ CPS900®

Delete a job from the mailbox

Introduction

The jobs in the 'Mailbox' are not deleted automatically after you print your jobs.

In the following situations, the jobs in the set memory are automatically deleted.

■

The key operator must do a key operator maintenance ('KOM') action. The Océ
CPS900

turns off and all the jobs are deleted.

■

The Océ CPS900

enters 'Sleep mode' or 'Low power mode'. The system setting

'Keep data in ECO mode' is set to 'No'.

■

The Océ CPS900

shuts down.

Purpose

The mailbox is not a storage area for print jobs. The productivity of the Océ
CPS900

decreases if the completed jobs are not deleted at regular intervals.

Note:

The 'Delete' function is not reversible and the Océ CPS900

will not ask you

to confirm the 'Delete' action.

Illustration

[25]

[25] Delete a job from the mailbox

Summary of Contents for CPS900











































































































































Search results

Summary of Contents for CPS900

Reviews:

Related manuals for CPS900

Brands by name

Popular brands

Oce CPS900, User Manual

Search results

Summary of Contents for CPS900

Reviews:

Related manuals for CPS900

Brands by name

Popular brands