Oce Arizona 318 GL User Manual Download Page 204 | Manualshive

Page: 204 / 224

background image

2.

Disconnect the UV lamp housing power cable connector by pressing in the two blue tabs on
either side and pull it out.

[143] Disconnect power cable

3.

Remove the foam filter from the top of the housing by lifting the exposed edge as shown below.
It is flexible and will bend as you remove it.

[144] Remove Lamp Filter

4.

Swing the UV lamp housing interlock safety arm out of the way:

[145] Interlock Safety Arm

• first lift it straight up to the height of the blue connector;
• then angle it away from the connector as you raise it higher; and
• finally swing the arm back over the connector and past the raised part of the lamp housing.

NOTE

The UV lamp housing cannot be removed from the carriage until the bracket is swung
out of the way.

5.

Lift the UV lamp housing straight up and out of its carriage bucket.

How to Change a UV Lamp Bulb

204

Chapter 11 - Printer Maintenance

«
...
202
203
204
205
206
...
»

Summary of Contents for Arizona 318 GL

































































































































































































































Reviews:

No comments

Related manuals for Arizona 318 GL

Brand: V-King Pages: 41

Brand: QMS Pages: 208

Brand: uBuild-3D Pages: 12

4250 - WorkCentre - Copier

Brand: Xerox Pages: 210

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 4

4118P - WorkCentre B/W Laser

Brand: Xerox Pages: 16

3635MFP - Phaser B/W Laser

Brand: Xerox Pages: 10

3635MFP - Phaser B/W Laser

Brand: Xerox Pages: 42

3300MFP - Phaser B/W Laser

Brand: Xerox Pages: 148

3250D - Phaser B/W Laser Printer

Brand: Xerox Pages: 12

Brand: Xerox Pages: 4

Brand: Xerox Pages: 12

Brand: Xerox Pages: 12

4250 - WorkCentre - Copier

Brand: Xerox Pages: 16

Brand: Xante Pages: 6

WorkCentre 7800 series

Brand: Xerox Pages: 14

WORKCENTRE 7775

Brand: Xerox Pages: 15

WORKCENTRE 7775

Brand: Xerox Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands