Oce Arizona 318 GL User Manual Download Page 187 | Manualshive

Page: 187 / 224

background image

Empty Ink Waste Trays

Introduction

There are two waste trays. The Purge Waste Tray is located under the Maintenance station. It
catches ink purged from either Manual maintenance or Automated printhead maintenance. The
Spit Waste Tray is located below the ink spit catcher. It accumulates waste ink from printhead
spitting.

[133] 1 = Purge Waste Tray 2 = Spit Waste Tray

When to do

Empty both waste trays weekly.

CAUTION

Both ink waste trays contain uncured ink. For safety reasons, it is necessary to wear nitrile
gloves, a lab coat and safety glasses with side shields to protect users from contacting the ink.
UV-curable inks contain chemicals which can lead to sensitization with prolonged or repeated
exposure to skin. These chemicals inside the UV ink can begin to penetrate the gloves in less
than 10 minutes. Since they have no pigment, exposure is not obvious. Therefore, Océ
recommends that only approved nitrile gloves are used for a maximum of 10 minutes after
being contaminated with ink and never reused. Damaged gloves should be changed
immediately (see the Maintenance Guidelines section and Safety chapter for more details on
the recommended nitrile gloves). .

NOTE

Although the carriage is oriented so that the nozzles spit into the slots in the spit catcher, some
ink will find its way onto the flat surfaces. Open the maintenance drawer to check the surface of
the spit catcher daily. If you see any ink wipe it up with a clean cloth or paper towel.

Equipment

• Foam Tipped Swab or Cloth-Poly Wipe
• An empty semi-transparent 1.0 liter plastic container for the Spit Waste tray
• An empty semi-transparent 5 liter plastic container for the Purge Waste tray

Empty Ink Waste Trays

Chapter 11 - Printer Maintenance

187

«
...
185
186
187
188
189
...
»

Summary of Contents for Arizona 318 GL

































































































































































































































Reviews:

No comments

Related manuals for Arizona 318 GL

Brand: G3D Pages: 4

Brand: Nanoptix Pages: 25

Brand: Nanoptix Pages: 4

VarioPrint 1055

Brand: OcÃ© Pages: 194

Brand: Oce Pages: 12

Brand: Oki Pages: 2

OKIPAGE 8c Plus

Brand: Oki Pages: 48

Brand: Oki Pages: 257

Brand: Oki Pages: 113

Brand: Oki Pages: 26

Brand: Oki Pages: 183

Brand: Oki Pages: 36

Brand: Oki Pages: 136

Brand: Oki Pages: 66

Brand: Oki Pages: 123

Brand: Oki Pages: 109

Brand: Oki Pages: 68

Brand: Oki Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands