Oce Arizona 318 GL User Manual Download Page 57 | Manualshive

Page: 57 / 224

background image

Software Update Module

Introduction

As we are committed to improve and refine the quality and functionality of the Océ Arizona 318
GL printer, there will be periodic upgrades to the underlying firmware and printer software.
Software updates are available only to customers with a service contract. Your local service
representative will either install the upgrade or provide you with the upgrade file in some
circumstances.

Illustration

How to Upgrade the Firmware and Software

Your dealer or service representative will advise you when an update of the printer software is
necessary. If they request that you install the upgrade, an unzip password will be provided and
instructions are available from the DGS website when the update file is downloaded.

Software Update Module

Chapter 4 - How to Navigate the User Interface

57

«
...
55
56
57
58
59
...
»

Summary of Contents for Arizona 318 GL

































































































































































































































Reviews:

No comments

Related manuals for Arizona 318 GL

Brand: SA Pages: 5

Brand: Tally Pages: 53

T2265 SprintPro

Brand: Tally Pages: 30

Brand: Tally Pages: 108

Brand: TallyGenicom Pages: 2

Brand: TallyGenicom Pages: 2

Brand: Canon Pages: 37

WorkCentre Pro 123

Brand: Xerox Pages: 4

DocuCentre SC2020

Brand: Xerox Pages: 322

Brand: Xerox Pages: 2

Brand: Xerox Pages: 8

Brand: Xerox Pages: 80

Brand: Xerox Pages: 38

WorkCentre 7132

Brand: Xerox Pages: 73

DocuPrint C3055 DX

Brand: Xerox Pages: 20

Brand: Oki Pages: 197

Brand: Ricoh Pages: 781

Brand: Konica Minolta Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands