manualshive.com logo in svg

NXP Semiconductors MPC555, User Manual

The NXP Semiconductors MPC555 is a cutting-edge microcontroller designed for versatile applications. Enhance your product development experience with our comprehensive User Manual, available for free download at manualshive.com. Discover detailed instructions and unleash the full potential of the MPC555 to transform your projects.

Share
Download
background image

MPC555

 / 

MPC556

QUEUED SERIAL MULTI-CHANNEL MODULE

MOTOROLA

USER’S MANUAL

Rev. 15 October  2000

14-55

in the serial data stream, which makes SCIx tolerant to small frequency variations in
the received data stream.

The sequence of events used by the receiver to find a start bit is listed below.

1. Sample RXDx input during each RT period and maintain these samples in a se-

rial pipeline that is three RT periods deep.

2. If RXDx is low during this RT period, go to step 1.
3. If RXDx is high during this RT period, store sample and proceed to step 4.
4. If RXDx is low during this RT period, but not high for the previous three RT pe-

riods (which is noise only), set an internal working noise flag and go to step 1,
since this transition was not a valid start bit transition.

5. If RXDx is low during this RT period and has been high for the previous three

RT periods, call this period RT1, set RAF, and proceed to step 6.

6. Skip RT2 but place RT3 in the pipeline and proceed to step 7.
7. Skip RT4 and sample RT5. If both RT3 and RT5 are high (RT1 was noise only),

set an internal working noise flag. Go to step 3 and clear RAF. Otherwise, place
RT5 in the pipeline and proceed to step 8.

8. Skip RT6 and sample RT7. If any two of RT3, RT5, or RT7 is high (RT1 was

noise only), set an internal working noise flag. Go to step 3 and clear RAF. Oth-
erwise, place RT7 in the pipeline and proceed to step 9.

9. A valid start bit is found and synchronization is achieved. From this point on until

the end of the frame, the RT clock will increment starting over again with RT1
on each one-to-zero transition or each RT16. The beginning of a bit-time is thus
defined as RT1 and the end of a bit-time as RT16.

Upon detection of a valid start bit, synchronization is established and is maintained
through the reception of the last stop bit, after which the procedure starts all over again
to search for a new valid start bit. During a frame's reception, SCIx resynchronizes the
RT clock on any one-to-zero transitions.

Additional logic in the receiver bit processor determines the logic level of the re-ceived
bit and implements an advanced noise-detection function. During each bit-time of a
frame (including the start and stop bits), three logic-sense samples are taken at RT8,
RT9, and RT10. The logic sense of the bit-time is decided by a majority vote of these
three samples. This logic level is shifted into register RDRx for every bit except the
start and stop bits.

If RT8, RT9, and RT10 do not all agree, an internal working noise flag is set. Addition-
ally for the start bit, if RT3, RT5, and RT7 do not all agree, the internal working noise
flag is set. If this flag is set for any of the bit-times in a frame, the NF flag in SCxSR is
set concurrently with the RDRF flag in SCxSR when the data is transferred to register
RDRx. The user must determine if the data received with NF set is valid. Noise on the
RXDx pin does not necessarily corrupt all data.

The operation of the receiver bit processor is shown in 

Figure 14-14

. This example

demonstrates the search for a valid start bit and the synchronization procedure as out-
lined above. The possibilities of noise durations greater than one bit-time are not con-
sidered in this examples.

 

   

  

F

re

e

sc

a

le

 S

e

m

ic

o

n

d

u

c

to

r,

 I

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

 

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

n

c

.

..

Summary of Contents for MPC555








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC555

Qorvo MDEK1001 Quick Start Manual preview
MDEK1001
Brand: Qorvo Pages: 8
ASROCK Fatal1ty Z170 Gaming K4 Series Manual preview
Fatal1ty Z170 Gaming K4 Series
Brand: ASROCK Pages: 163
AOpen MX46S Manual preview
MX46S
Brand: AOpen Pages: 96
Intel DH67CL Product Manual preview
DH67CL
Brand: Intel Pages: 78
MSI MS-7277 Instruction Manual preview
MS-7277
Brand: MSI Pages: 94
IEI Technology IMBA-G412ISA-R20 User Manual preview
IMBA-G412ISA-R20
Brand: IEI Technology Pages: 164
AMPTRON PII-3100 User Manual preview
PII-3100
Brand: AMPTRON Pages: 16
Quick BT386HY455 User Manual preview
BT386HY455
Brand: Quick Pages: 32
JETWAY MM91 Series User Manual preview
MM91 Series
Brand: JETWAY Pages: 38
BESTEK BNX-A110 User Manual preview
BNX-A110
Brand: BESTEK Pages: 47
Ublox EVK-ANNA-B4 User Manual preview
EVK-ANNA-B4
Brand: Ublox Pages: 42
Gigabyte X570S AORUS PRO AX User Manual preview
X570S AORUS PRO AX
Brand: Gigabyte Pages: 52
Supermicro X11SPG-TF User Manual preview
X11SPG-TF
Brand: Supermicro Pages: 124
Supermicro X11SCE-F User Manual preview
X11SCE-F
Brand: Supermicro Pages: 95
Supermicro X11DPS-RE User Manual preview
X11DPS-RE
Brand: Supermicro Pages: 229
NXP Semiconductors i.MX RT1020 Quick Start Manual preview
i.MX RT1020
Brand: NXP Semiconductors Pages: 4
MSI MS-98L9 Manual preview
MS-98L9
Brand: MSI Pages: 58
Fujitsu CPU369-Module Documentation preview
CPU369-Module
Brand: Fujitsu Pages: 12

Brands by name

Popular brands

Load more brands