manualshive.com logo in svg

NXP Semiconductors MPC555, User Manual

The NXP Semiconductors MPC555 is a cutting-edge microcontroller designed for versatile applications. Enhance your product development experience with our comprehensive User Manual, available for free download at manualshive.com. Discover detailed instructions and unleash the full potential of the MPC555 to transform your projects.

Share
Download
background image

MPC555

 / 

MPC556

QUEUED ANALOG-TO-DIGITAL CONVERTER MODULE-64

MOTOROLA

USER’S MANUAL

Rev. 15 October  2000

13-14

13.9.2 Front-End Analog Multiplexer

The internal multiplexer selects one of the 16 analog input pins or one of three special
internal reference channels for conversion. The following are the three special chan-
nels:

• V

RH 

— Reference Voltage High

• V

RL 

— Reference Voltage Low

• (V

RH

 – V

RL

)/2 — Mid-Reference Voltage

The selected input is connected to one side of the DAC capacitor array. The other side
of the DAC array is connected to the comparator input. The multiplexer also includes
positive and negative stress protection circuitry, which prevents other channels from
affecting the present conversion when excessive voltage levels are applied to the oth-
er channels.

13.9.3 Digital-to-Analog Converter Array

The digital-to-analog converter (DAC) array consists of binary-weighted capacitors
and a resistor-divider chain. The array serves two purposes: 

• The array holds the sampled input voltage during conversion
• The resistor-capacitor array provides the mechanism for the successive approx-

imation A/D conversion

Resolution begins with the MSB and works down to the LSB. The switching sequence
is controlled by the SAR logic.

13.9.4 Comparator

The comparator is used during the approximation process to sense whether the digi-
tally selected arrangement of the DAC array produces a voltage level higher or lower
than the sampled input. The comparator output feeds into the SAR which accumulates
the A/D conversion result sequentially, starting with the MSB.

13.9.5 Successive Approximation Register

The input of the successive approximation register (SAR) is connected to the compar-
ator output. The SAR sequentially receives the conversion value one bit at a time,
starting with the MSB. After accumulating the ten bits of the conversion result, the SAR
data is transferred by the queue control logic in the digital section to the appropriate
result location, where it may be read by user software.

13.10 Digital Control Subsystem

The digital control subsystem includes the clock and periodic/interval timer, control
and status registers, the conversion command word table RAM, and the result word
table RAM.

The central element for control of the QADC64 conversions is the 64-entry CCW table.
Each CCW specifies the conversion of one input channel. Depending on the applica-
tion, one or two queues can be established in the CCW table. A queue is a scan se-
quence of one or more input channels. By using a pause mechanism, sub-queues can

 

   

  

F

re

e

sc

a

le

 S

e

m

ic

o

n

d

u

c

to

r,

 I

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

 

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

n

c

.

..

Summary of Contents for MPC555








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC555

4gon RouterBOARD 411 Quick Setup Manual And Warranty Information preview
RouterBOARD 411
Brand: 4gon Pages: 2
SOYO KT333 DRAGON Plus Quick Start Manual preview
KT333 DRAGON Plus
Brand: SOYO Pages: 34
Octek RHINO VAP133-ACP User Manual preview
RHINO VAP133-ACP
Brand: Octek Pages: 66
MSI nF725GM-P User Manual preview
nF725GM-P
Brand: MSI Pages: 169
Gigabyte GA-P61-USB3P User Manual preview
GA-P61-USB3P
Brand: Gigabyte Pages: 100
Aaeon SBC-770 User Manual preview
SBC-770
Brand: Aaeon Pages: 111
Memec Virtex-4 User Manual preview
Virtex-4
Brand: Memec Pages: 45
Lite-on Tech NA280 User Manual preview
NA280
Brand: Lite-on Tech Pages: 49
Global American 3307740 User Manual preview
3307740
Brand: Global American Pages: 132
Analog Devices UG-388 User Manual preview
UG-388
Brand: Analog Devices Pages: 8
IEI Technology JUKI-6770 User Manual preview
JUKI-6770
Brand: IEI Technology Pages: 53
DFI PM10-EC User Manual preview
PM10-EC
Brand: DFI Pages: 93
DFI SD330-Q170 User Manual preview
SD330-Q170
Brand: DFI Pages: 79
Garmin Force Trolling Motor 50" Service Alert preview
Force Trolling Motor 50"
Brand: Garmin Pages: 76
Asus I220GC User Manual preview
I220GC
Brand: Asus Pages: 82
Asus H81M-E R2.0 User Manual preview
H81M-E R2.0
Brand: Asus Pages: 46
Asus H81M-K User Manual preview
H81M-K
Brand: Asus Pages: 48
Asus H81M-R Manual preview
H81M-R
Brand: Asus Pages: 48

Brands by name

Popular brands

Load more brands