Nortel Passport 8600 Series Commissioning Download Page 94

Page: 94 / 136

Initial steps using the NNCLI

Variable

Value

default-lockout-time

<60-65000>

Changes the default lockout time after
three invalid attempts. Configures the
lockout time, in seconds, and is in the
60–65000 range. The default is 60
seconds.

To configure this option to the default
value, use the

default

operator with

the command.

lockout <word> time <time>

Configures the host lockout time.

•

word

is the host IP address in the

format a.b.c.d.

•

time

is the lockout-out time, in

seconds, in the 60–65000 range.
The default is 60 seconds.

min-passwd-len <10-20>

Configures the minimum length for
passwords in high-secure mode.

To configure this option to the default
value, use the

default

operator with

the command.

password-history <3-32>

Specifies the number of previous
passwords the switch stores. You
cannot reuse a password that is stored
in the password history. The default is
3.

To configure this option to the default
value, use the

default

operator with

the command.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands