Nortel Passport 8600 Series Commissioning Download Page 131

Page: 131 / 136

131

Common procedures using the NNCLI

The following section describes common procedures you use while
commissioning the Nortel Ethernet Routing Switch 8600.

Common procedure navigation

•

“Saving the configuration” (page 131)

Saving the configuration

After you change the boot configuration, you must save the changes
to both the master and the standby management modules. Save the
configuration to a file to retain the configuration settings.

Prerequisites

•

You must log on to the Privileged EXEC mode in the NNCLI.

Procedure steps

Step

Action

Save to boot configuration by using the following command:

save bootconfig [file <word>] [verbose] [standby <word>]

[backup <word>] [mode <cli|nncli>]

Save the running configuration by using the following command:

save config [file <word>] [verbose] [standby <word>]

[backup <word>] [mode (cli|nncli)]

--End--

Variable definitions

Use the data in the following table to use the

save bootconfig

and

save config

commands.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands