Nortel Passport 8600 Series Commissioning Download Page 93

Page: 93 / 136

Changing passwords

Configure password options by using the following command:

password [access-level <word>] [aging-time day <1-365>]

[default-lockout-time <60-65000>] [lockout <word> time

<time>] [min-passwd-len <10-20>] [password-history

<3-32>]

--End--

Variable definitions

Use the data in the following table to use the password commands.

Variable

Value

access level <word>

Permits or blocks this access level.
The available access level values are:

•

l4admin

•

l4oper

•

layer1 <word>

•

layer2

•

layer3 <word>

•

oper

•

read-only <word>

•

read-write <word>

•

read-write-all <word>

•

slbadmin

•

slboper

•

ssladmin

<word>

represents the new password

with 0–20 characters.

For information about the Web
Switching Module (WSM), see Nortel
Ethernet Routing Switch 8600 Web
Switching Module Fundamentals,
NN46205-314.

aging-time day <1-365>

Configures the expiration period for
passwords in days, from 1–365.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands