Nortel Passport 8600 Series Commissioning Download Page 75

Page: 75 / 136

Connecting a modem

ATTENTION

Nortel recommends that before you configure the Serial Line Internet
Protocol (SLIP) or the Point-to-Point Protocol (PPP), you familiarize
yourself with these protocols.

If you configure the port mode to

slip

, use the following

command to configure other SLIP parameters:

boot config sio modem [slip-compression] [slip-rx-comp

ression]

If you configure the port mode to

ppp

, use the following

commands to configure other PPP parameters:

boot config sio modem [mtu <bytes>] [my-ip <ipaddr>]

[peer-ip <ipaddr>] pppfile <file>

On the modem, turn off echo mode and return code messaging.

Connect the modem to the modem port.

Save the boot configuration.

Optionally, shutdown and reinitialize the port by using the
following command:

boot config sio modem restart

Reboot the switch.

--End--

Variable definitions

Use the data in the following table to use the

boot config sio

command.

Variable

Value

8databits

Specifies either 8 (enabled) or 7 (disabled)
data bits for each byte for software to interpret.
The default is disabled. Use the

operator

to remove this configuration. To configure this
option to the default value, use the

default

operator with the command.

baud <rate>

Configures the baud rate for the port. The
default is 9600. To configure this option to the
default value, use the

default

operator with the

command.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands