Nortel Passport 8600 Series Commissioning Download Page 51

Page: 51 / 136

Connecting a modem

Table 7
Job aid: PPP file options (cont’d.)

Option

Description

ipcp_max_failure <value>

Configures the maximum number
of IPCP configuration negative
acknowledgements (NAK) to the value
you specify.

ipcp_max_terminate <value>

Configures the maximum number of
transmissions for IPCP termination
requests to the value you specify.

ipcp_restart <value>

Configures the timeout, in seconds,
for IPCP negotiation to the value you
specify.

lcp_echo_failure <value>

Configures the maximum consecutive
Link Control Protocol (LCP) echo
failures to the value you specify.

lcp_echo_interval <value>

Configures the interval, in seconds,
between LCP echo requests to the
value you specify.

lcp_max_configure <value>

Configures the maximum number of
transmissions for LCP configuration
requests to the value you specify.

lcp_max_failure <value>

Configures the maximum number of
LCP configuration NAKs to the value
you specify.

lcp_max_terminate <value>

Configures the maximum number of
transmissions for LCP termination
requests to the value you specify.

lcp_restart <value>

Configures the timeout in seconds for
the LCP negotiation to the value you
specify.

local_auth_name <name>

Configures the local name for
authentication to the specified name.

login

Uses the logon password database
for Password Authentication Protocol
(PAP) peer authentication.

max_challenge <value>

Configures the maximum number of
transmissions for CHAP challenge
requests to the value you specify.

mru <value>

Configures the maximum receive unit
(MRU) size for negotiation to the value
you specify.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands