Nortel Passport 8600 Series Commissioning Download Page 89

Page: 89 / 136

Configuring the time zone

Example of configuring system identification

Procedure steps

Step

Action

Change the system name by using the following command:

ERS-8610:5(config)#sys name ERS-8610

Configure the system contact by using the following command:

ERS-8610:5(config)#snmp-server contact
[email protected]

Configure the system location by using the following command:

ERS-8610:5(config)#snmp-server location "12 Main
St, Vancouver, BC"

--End--

Configuring the time zone

Configure the time zone to specify the time zone for your location and
configure settings for Daylight Saving Time (DST).

Prerequisites

•

You must log on to the Global Configuration mode in the NNCLI.

Procedure steps

Step

Action

Configure the time zone by using the following command:

boot config tz

Save the changed configuration to the boot.cfg and pcmboot.cfg
files.

Reboot the switch.

--End--

Variable definitions

Use the data in the following table to use the

boot config tz

command.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands