Nortel Passport 8600 Series Commissioning Download Page 90

Page: 90 / 136

Initial steps using the NNCLI

Variable

Value

dst-end <Mm.n.d/hhmm|MMddh

hmm>

Configures the ending date of DST. You
can specify the time in one of two ways:

•

Mm.n.d/hhmm

specifies an hour on

the nth occurrence of a weekday in a
month. For example,

M10.5.0/0200

means the fifth occurrence of Sunday
in the tenth month (October) at 2:00
a.m.

•

MMddhhmm

specifies a month, day,

hour, and minute. For example,

10310200

means October 31 at 2:00

a.m.

dst-name <dstname>

Configures an abbreviated name for the
local daylight saving time zone.

dstname

is the name. For example, PDT is Pacific
Daylight Time.

To configure this option to the default
value, use the

default

operator with the

command.

dst-offset <minutes>

Configures the daylight saving adjustment
in minutes.

The default is 60 minutes.

To configure this option to the default
value, use the

default

operator with the

command.

dst-start <Mm.n.d/hhmm|MMd

dhhmm>

Configures the starting date of DST.

•

Mm.n.d/hhmm

specifies an hour on

the nth occurrence of a weekday in a
month. For example,

M10.5.0/0200

means the fifth occurrence of Sunday
in the tenth month (October) at 2:00
a.m.

•

MMddhhmm

specifies a month, day,

hour, and minute. For example,

10310200

means October 31 at 2:00

a.m.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands