Nortel Passport 8600 Series Commissioning Download Page 132

Page: 132 / 136

132

Common procedures using the NNCLI

Variable

Value

backup <word>

Saves the specified file name and
identifies the file as a backup file.

word

uses one of the following

formats:

•

[a.b.c.d]:<file>

•

peer/<file>

•

/pcmcia/ <file>

•

/flash/ <file>

file is a string of 1–99 characters.

file <word>

Specifies the file name in one of the
following formats for

word

•

[a.b.c.d]: <file>

•

peer/<file>

•

/pcmcia/ <file>

•

/flash/ <file>

file is a string of 1–99 characters.

mode <cli|nncli>

Saves the boot configuration in CLI or
NNCLI format.

standby <word>

Saves the specified file name to the
standby SF/CPU in the following
format for

word

•

filename, /pcmcia/ <file>

•

/flash/ <file>

file is a string of 1–99 characters.

verbose

Saves the default and current
configuration. If you omit this
parameter, the command saves
only parameters you change.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands