Nortel Passport 8600 Series Commissioning Download Page 60

Page: 60 / 136

Initial steps using the CLI

Configuring system identification

Configure system identification to specify the system name, contact
person, and location of the switch.

Procedure steps

Step

Action

Specify the system name by using the following command:

config sys set name <prompt>

Specify the name of the contact person for the switch by using
the following command:

config sys set contact <contact>

Define the location for the system by using the following
command:

config sys set location <location>

--End--

Variable definitions

Use the data in the following table to use the

config sys set

command.

Variable

Value

clipId-topology-ip <id>

Sets the topology IP from the
available CLIP.

is the circless IP

interface id in the range of 1 to 256.

clock-sync-time <minutes>

Configures the RTC-to-system clock
synchronization time.

minutes

is the

RTC-to-System clock synchronization
time in minutes in the range of 15 to
3600.

contact <contact>

Alters the system contact.

contact

the system contact. The string length
is in the range of 0 to 255.

ecn-compatibility <enable|dis

able>

Enables or disables ecn-compatibility
feature.

force-topology-ip-flag

<true|false>

Sets flag to force choice of
topology-IP.

true|false

Enables or

disables Force Topology IP Flag.

global-filter <enable|disable>

Enables global filter feature.

info

Shows current level parameter
settings and next level directories.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands