Nortel Passport 8600 Series Commissioning Download Page 37

Page: 37 / 136

Configuring the date and time

Variable

Value

•

saveSlaveBootConfig—saves the
current boot configuration to the
standby SF/CPU

•

loadLicense—loads a software license
file to enable features

ActionGroup2

Can be one of the following actions:

•

resetlstStatCounters—resets the IST
statistic counters

•

resetLspStats—resets the LSP
statistics

ActionGroup3

flushIpRouteTbl—flushes IP routes from
the routing table

ActionGroup4

Can be one of the following actions:

•

hardReset—resets the device and runs
power-on tests.

•

softReset—resets the device without

running power-on tests

•

cpuSwitchOver—switch control from
one SF/CPU to another

•

resetConsole—reinitializes the

hardware UART drivers. Use only if the
console or modem connection is hung

•

resetModem—reinitializes the UART

drivers on the modem port. Use only
if the console or modem connection is
hung

Result

Displays a message after you click Apply

Configuring the date and time

Use the User Set Time tab to configure the date and time.

Procedure steps

Step

Action

In the Device Manager window, select the chassis.

From the Device Manager menu bar, choose Edit, Chassis.

The Chassis dialog box appears with the System tab displayed.

Click User Set Time.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands