Nortel Passport 8600 Series Commissioning Download Page 110

Page: 110 / 136

110

Remote connection configuration using the CLI

Variable

Value

enable

Enables the Ethernet
Routing Switch Web
interface.

password <ro> <username> <password>

Configures passwords for
access to the Web interface.

username

is the user logon

name (up to 20 characters).

password

is the password

associated with the logon
name (up to 20 characters).

Configuring the remote host logon

Configure the remote host logon to modify parameters for FTP and TFTP
access. Use the default parameters for TFTP transfers. If you want to use
FTP as the transfer mechanism, you need to change the password to a
valid value.

Procedure steps

Step

Action

Define conditions for the remote host logon by using the
following command:

config bootconfig host

Save the changed configuration to the boot.cfg and pcmboot.cfg
files.

Reboot the switch.

--End--

Variable definitions

Use the data in the following table to use the

config bootconfig host

command.

Variable

Value

ftp-debug

<true|false>

Enables or disables debug mode on FTP. If you
enable debug mode, debug messages appear on the
management console screen. The default is false.

info

Displays the current remote host logon settings.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands