Nortel Passport 8600 Series Commissioning Download Page 109

Page: 109 / 136

Enabling the Web management interface

109

Enable or disable the access service by using the following
command:

flags <access-service> <true|false>

Save the boot configuration.

--End--

Variable definitions

Use the data in the following table to use the

flags

command.

Variable

Value

access-service

Specifies the type of remote access
service as one of the following:

•

ftpd

•

rlogind

•

telnetd

•

tftpd

•

sshd

true|false

True enables the service. False
disables the service.

Enabling the Web management interface

Start the Web management interface to provide management access to
the switch using a Web browser. For details about configuring the Web
management interface, see Nortel Ethernet Routing Switch User Interface
Fundamentals, NN46205-308.

Procedure steps

Step

Action

Enable the Web server by using the following command:

config web-server enable

Configure the access password by using the following command:

config web-server password <ro> <username> <password>

--End--

Variable definitions

Use the data in the following table to use the

config web-server

command.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands