manualshive.com logo in svg

Nortel Passport 8600 Series, Commissioning

Share
Download
Nortel Passport 8600 Series Commissioning Download Page 121

Configuring the remote host logon

121

3

Reboot the switch.

--End--

Variable definitions

Use the data in the following table to use the

boot config host

command.

Variable

Value

ftp-debug

Enables or disables debug mode on FTP. If you
enable debug mode, debug messages appear on the
management console screen. The default is disabled.
Use the

no

operator to later remove this configuration.

To configure this option to the default value, use the

default

operator with the command.

password <value>

Configures the password to enable FTP transfers.

value

is the password, up to 16 characters long.

After you configure this password, only FTP is used for
remote host logon

ATTENTION

This password must match the password for the
FTP server, or the FTP operation fails. Also, if you
configure the password to a valid value, then all
copying to and from the network uses FTP instead
of TFTP. If the user name or password is incorrect,
copying over the network fails.

tftp-debug

Enables or disables debug mode on TFTP/TFTPD.
If you enable debug mode, debug messages display
on the management console screen. The default
is disabled. Use the

no

operator to remove this

configuration. To configure this option to the default
value, use the

default

operator with the command.

tftp-hash

Enables or disables the TFTP hash bucket display.
The default is disabled. Use the

no

operator to remove

this configuration. To configure this option to the
default value, use the

default

operator with the

command.

tftp-rexmit

<seconds>

Configures the TFTP retransmission timeout. The
default value is 2 seconds.

seconds

is the number of

seconds (1–120).

To configure this option to the default value, use the

default

operator with the command.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands