manualshive.com logo in svg

Nortel Passport 8600 Series, Commissioning

Share
Download
Nortel Passport 8600 Series Commissioning Download Page 66

66

Initial steps using the CLI

l1 <username> [ <password> ]

Changes the Layer 1 read/write
logon or password.

•

username

is the logon name

•

password

is the password

associated with the logon
name.

l2 <username> <password>

Changes the Layer 2 read/write
logon or password.

•

username

is the logon name.

l3 <username> [ <password> ]

Changes the Layer 3 read/write
logon and/or password (applies
only to the Nortel Ethernet
Routing Switch 8600).

•

username

is the logon name.

•

password

is the password

associated with the logon
name.

l4admin <username>

Configures the Layer 4
administrator logon to connect
to the Web Switching Module
(WSM). For more information
about the WSM, see Nortel
Ethernet Routing Switch
8600 Web Switching Module
Fundamentals, NN46205-314.

l4oper <username>

Configures the Layer 4 operator
logon to connect to the WSM.
For more information about
the WSM, see Nortel Ethernet
Routing Switch 8600 Web
Switching Module Fundamentals,
NN46205-314.

lockout-time <HostAddress> <secs>

Configures the host lockout time.

•

HostAddress

is the host IP

address in the format a.b.c.d.

•

secs

is the lockout time limit

in seconds for passwords
lockout in the 60–65000
range. The default is 60
seconds.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands