Nortel Passport 8600 Series Commissioning Download Page 62

Page: 62 / 136

Initial steps using the CLI

Configuring the time zone

Set the time zone to specify the time zone for your location and configure
settings for Daylight Saving Time (DST).

Procedure steps

Step

Action

Configure the time zone by using the following command:

config bootconfig tz

Save the changed configuration to the boot.cfg and pcmboot.cfg
files.

Reboot the switch.

--End--

Variable definitions

Use the data in the following table to use the

config bootconfig tz

command.

Variable

Value

dst-end

<Mm.n.d/hhmm|MMddhhmm>

Configures the ending date of DST. You
can specify the time in one of two ways:

•

Mm.n.d/hhmm

specifies an hour on

the nth occurrence of a weekday in a
month. For example,

M10.5.0/0200

means the fifth occurrence of Sunday
in the tenth month (October) at 2:00
a.m.

•

MMddhhmm

specifies a month, day,

hour, and minute. For example,

10310200

means October 31 at 2:00

a.m.

dst-name <dstname>

Configures an abbreviated name for the
local daylight saving time zone.

dstname

is the name. For example, PDT is Pacific
Daylight Time.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands