Nortel Passport 8600 Series Commissioning Download Page 36

Page: 36 / 136

Initial steps using Device Manager

Variable

Value

LastVlanChange

Displays the time since the last VLAN
change

LastStatisticsReset

Displays the time since the statistics
counters were last reset

LastRunTimeConfigSave

Displays the last run-time configuration
saved

LastRunTimeConfigSaveToSlave

Displays the last run-time configuration
saved to the standby device

LastBootConfigSave

Displays the last boot configuration saved

LastBootConfigSaveOnSlave

Displays the last boot configuration saved
on the standby device

DefaultRuntimeConfigFileName

Displays the default Run-time configuration
file directory name

DefaultBootConfigFileName

Displays the default boot configuration file
directory name

ConfigFileName

Specifies the name of a new configuration
file

ActionGroup1

Can be one of the following actions:

•

resetCounters—resets all statistic

counters

•

checkSwInFlash—checks the software
in flash

•

saveRuntimeConfigToSlave—saves
the current run-time configuration to the
standby SF/CPU

•

saveToNVRAM—saves the current
run-time configuration to nonvolatile
RAM (NVRAM)

•

checkSwInPcmcia—checks the
software in PCMCIA

•

saveBootConfig—saves the current
boot configuration

•

saveToStandbyNVRAM—saves the
current run-time configuration to the
standby NVRAM

•

saveRuntimeConfig—saves the current
run-time configuration

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Summary of Contents for Passport 8600 Series
































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands

Nortel Passport 8600 Series, Commissioning

Search results

Summary of Contents for Passport 8600 Series

Reviews:

Brands by name

Popular brands