NEC V854 UPD703006 User Manual Download Page 173 | Manualshive

Page: 173 / 417

background image

User’s Manual U11969EJ3V0UM00

173

CHAPTER 7 TIMER/COUNTER FUNCTION (REAL-TIME PULSE UNIT)

(8) Timer overflow status register (TOVS)

The overflow flags TM0 to TM3 are assigned.

This register can be read/written in 8- or 1-bit units.

By testing and resetting the TOVS register via software, occurrence of an overflow can be polled.

Bit Position

Bit Name

Function

7 to 0

OVFn

Overflow Flag
TMn overflow flag.

0: No overflow

1: Overflow

From TM0 and TM1, the interrupt requests (INTOV0 and INTOV1) are generated for the interrupt

controller in synchronization with the overflow

.

However, the interrupt operation and TOVS are

independent from each other, and the overflow flags (OVF0 and OVF1) from TM0 and TM1 can

be rewritten in the same manner as in other overflow flags.

At this time, the interrupt request flags (OVF0 and OVF1) corresponding to INTOV0 and INTOV1

are not affected.

No transmission is executed to the TOVS register during access from the CPU. Therefore, even
if an overflow occurs when the TOVS register is being read, the overflow flag value will not be

updated and this overflow condition will be reflected the next time the TOVS register is read.

Remark

n = 0, 1, 20 to 24, and 3

(9) External interrupt mode registers 1 to 4, 7 (INTM1 to INTM4, INTM7)

These registers set the following 3 types of valid edges:

• Sets valid edge of external interrupt request signal (INTP) when using CP10 to CP13 (timer 1), CC3,

CP3 (timer 3) as capture registers.

• Sets valid edges at external count clock input (TI) of timer 0, timer 1, and timer 2.

• Sets valid edges at timer clear (TCLR0) of timer 0.

For the details, refer to CHAPTER 5 INTERRUPT/EXCEPTION PROCESSING FUNCTION.

(10) Event divide counter 0 to 2 (EDV0 to EDV2)

Counts valid edges detected by the INTM1 to INTM3 registers. For the details, refer to 5.3 Maskable Interrupt.

(11) Event divide control register 0 to 2 (EDVC0 to EDVC2)

Sets the frequency division ratio of event divide counter (EDV0 to EDV2). For the details, refer to 5.3. Maskable

Interrupt.

(12) Event selection register (EVS)

Selects INTP signal to input to the EDV2 register. For the details, refer to 5.3 Maskable Interrupt.

Address

FFFFF230H

7

OVF3

TOVS

6

OVF24

5

OVF23

4

OVF22

3

OVF21

2

OVF20

1

OVF1

0

OVF0

After reset

00H

«
...
171
172
173
174
175
...
»

Summary of Contents for V854 UPD703006


































































































































































































































































































































































































































Reviews:

No comments

Related manuals for V854 UPD703006

Brand: Samsung Pages: 27

Brand: Lawler Pages: 4

Brand: QTP Pages: 2

Brand: MAKOT Pages: 6

Brand: Radware Pages: 98

Brand: Eaton Pages: 10

Brand: National Instruments Pages: 26

Brand: U-Tron Pages: 8

StarSign Bio Token 3.0 M

Brand: Giesecke & Devrient Pages: 28

Brand: maxon motor Pages: 44

Brand: Jung Pages: 8

Fair-Play MP-50 Series

Brand: Translux Pages: 20

Brand: National Instruments Pages: 20

Brand: Eliweli Pages: 2

IMPULSE G Plus Series 4

Brand: Magnetek Pages: 60

Brand: Altronix Pages: 20

Brand: ITRON Pages: 44

Brand: Heatpol Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands