NEC V854 UPD703006 User Manual Download

Page: 161 / 417

User’s Manual U11969EJ3V0UM00

161

CHAPTER 7 TIMER/COUNTER FUNCTION (REAL-TIME PULSE UNIT)

7.2.1 Timer 0

(1) Timers 0, 0L (TM0, TM0L)

TM0 functions as a 24-bit interval timer, free-running timer or event counter for external signals. It is used

to measure cycles and frequency, and also for pulse generation.

Only 32-bit read access is enabled for TM0 (however, the high-order 8 bits are fixed to 0), and only 16-bit read

access is enabled for TM0L.

To read the low-order 24 bits of timer 0, specify TM0 with word access, and to read the low-order 16 bits only,

specify TM0 with half-word access.

TM0 counts up the internal count clock or external count clock. The timer is started or stopped by the CE0

bit of timer control register 00 (TMC00).

(2) Capture/compare registers 00 to 03 (CC00 to CC03, CC00L to CC03L)

The capture/compare registers are 24-bit registers connected to TM0. They can be used as capture registers

or compare registers depending on the specification of timer control register 01 (TMC01).

32-bit read/write access is enabled for CC0n (however, the high-order 8 bits are fixed to 0, and are ignored

during write operation), and 16-bit read/write access is enabled for CC0nL.

To access the low-order 24 bits or the low-order 16 bits of these registers, specify CC0n and CC0nL,

respectively.

Remark n = 0 to 3

(a) When used as a capture register

When a capture/compare register is used as a capture register, it detects the valid edge of the

corresponding external interrupt INTPn (n = 10 to 13) as a capture trigger. Timer 0 latches the count value

in synchronization with the capture trigger (capture operation). The latched value is held by the capture

(b) When used as a compare register

When a capture/compare register is used as a compare register, it compares its contents with the value

of the timer at each clock tick.

Compare registers support the set/reset output function. In other words, they set or reset the corresponding

timer output synchronously with the coincidence signal generation.

24 23

TM0

Address

FFFFF250H

00000000

After reset

00000000H

TM0L

Address

FFFFF264H

At reset

0000H

24 23

CC0n

Addresses

FFFFF254H to
FFFFF260H

Addresses

FFFFF266H to
FFFFF26CH

00000000

After reset
Undefined

CC0nL

Summary of Contents for V854 UPD703006


































































































































































































































































































































































































































Search results

Summary of Contents for V854 UPD703006

Reviews:

Related manuals for V854 UPD703006

Brands by name

Popular brands

NEC V854 UPD703006, User Manual

Search results

Summary of Contents for V854 UPD703006

Reviews:

Related manuals for V854 UPD703006

Brands by name

Popular brands