NEC V854 UPD703006 User Manual Download Page 118

Page: 118 / 417

118

User’s Manual U11969EJ3V0UM00

CHAPTER 5 INTERRUPT/EXCEPTION PROCESSING FUNCTION

5.3.5 In-service priority register (ISPR)

This register holds the priority level of the maskable interrupt currently accepted. When an interrupt request is

accepted, the bit of this register corresponding to the priority level of that interrupt is set to 1 and remains set while

the interrupt is serviced.

When the RETI instruction is executed, the bit corresponding to the interrupt request having the highest priority

is automatically reset to 0 by hardware. However, it is not reset when execution is returned from non-maskable

processing or exception processing.

This register can be only read in 8- or 1-bit units.

Bit Position

Bit Name

Function

7 to 0

ISPR7 to

In-Service Priority Flag

ISPR0

Indicates priority of interrupt currently accepted

0: Interrupt request with priority n not accepted

1: Interrupt request with priority n accepted

Remark

n: 0 to 7 (priority level)

5.3.6 Maskable interrupt status flag (ID)

The interrupt disable status flag (ID) of the PSW controls the enabling and disabling of maskable interrupt requests.

Bit Position

Bit Name

Function

Interrupt Disable
Indicates enabling/disabling of maskable interrupt processing.

0: Maskable interrupt accepting enabled

1: Maskable interrupt accepting disabled (pending)

It is set to 1 by the DI instruction and reset to 0 by the EI instruction. Its value is

also modified by the RETI instruction or LDSR instruction when referencing the

PSW.

Non-maskable interrupt and exceptions are acknowledged regardless of this flag.

When a maskable interrupt is accepted, ID flag is automatically set to 1 by

hardware.

The interrupt request generated during the accepting disabled period (ID:1) is

accepted when the xxIFn bit of xxICn is set to 1, and ID flag is reset to 0.

Address

FFFFF166H

ISPR7

ISPR

ISPR6

ISPR5

ISPR4

ISPR3

ISPR2

ISPR1

ISPR0

After reset

00H

PSW

After reset

00000020H

SAT

S Z

Summary of Contents for V854 UPD703006


































































































































































































































































































































































































































Search results

Summary of Contents for V854 UPD703006

Reviews:

Related manuals for V854 UPD703006

Brands by name

Popular brands

NEC V854 UPD703006, User Manual

Search results

Summary of Contents for V854 UPD703006

Reviews:

Related manuals for V854 UPD703006

Brands by name

Popular brands