manualshive.com logo in svg

NEC V854 UPD703006, User Manual

Share
Download
NEC V854 UPD703006 User Manual Download Page 311

CHAPTER 9   A/D CONVERTER

User’s Manual  U11969EJ3V0UM00

311

9.6  Operation in the Timer Trigger Mode

The A/D converter can set conversion timings with the coincidence interrupt signals of the RPU compare register.

TM0 and the capture/compare register (CC03) are used for the timer for specifying the analog conversion trigger.

The following two modes are provided according to the specification of the TMC00 register.

(1) One-shot mode

To use the one-shot mode, 1 should be set to the OST0 bit of the TMC00 register (one-shot mode).

When the A/D conversion period is longer than the TM0 period, the TM0 generates an overflow, holds 000000H

and stops.  Thereafter, TM00 does not output the coincidence interrupt signal INTCC03 (A/D conversion

trigger) of the compare register, and the A/D converter goes into the A/D conversion standby state.  The TM0

count operation restarts when the valid edge of the TCLR0 pin input is detected or when 1 is written to the

CE0 bit of the TMC00 register.

(2) Loop mode

To use the loop mode, 0 should be set to the OST0 bit (normal mode) of the TMC00 register.

When the TM0 generates an overflow, the TM0 starts counting from 000000H again, and the coincidence

interrupt signal INTCC03 (A/D conversion trigger) of the compare register is repeatedly output and A/D

conversion is also repeated.

Coincidence of the compare register can also clear TM0 and restart it.

9.6.1  Select mode operation

The A/D converter converts an analog input (ANI0 to ANI15) specified by the ADM0 register.  The conversion results

are stored in the ADCRn register corresponding to the analog input.  For the select mode, the one-buffer mode and

four-buffer mode are provided according to the storing method employed for the A/D conversion results.

(1) 1-buffer mode operation (Timer trigger select: 1-buffer)

The A/D converter converts one analog input once and stores the conversion results in one ADCRn register

(Refer to Table 9-4, Figure 9-9).

The A/D converter converts one analog input once using the trigger of the coincidence interrupt signal

(INTCC03) and stores the results in one ADCRn register.

An INTAD interrupt is generated for each A/D conversion and the A/D conversion is ended.

When TM0 is set to the one-shot mode, A/D conversion is ended after one conversion operation.  To restart

the A/D conversion, input the valid edge to the TCLR0 pin or write 1 to the CE0 bit of the TMC00 register.

When TM0 is set to the loop mode, A/D conversion is repeated each time the coincidence interrupt is generated,

unless the CE bit of the ADM0 register is set to 0.

Summary of Contents for V854 UPD703006


































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands