NEC UNIVERGE GT890 User Manual Download Page 133

Page: 133 / 297

132

Note:



When the call is picked up, the screen shows the number of call destination (and name when it

registered to contacts).



When the call cannot be picked up, the screen shows “Your call was disconnected by the system
(404)”.

Voicemail

This section describes how to use voicemail.

Note:



Previous setting of voicemail access code is required to use voicemail. Access codes are

configured according to your environment. If you are not sure what code to set, contact your

system administrator.



In PBX "DTMF Relay Mode" should be set to

”RFC2833” for wireless network.

To preset access codes for voicemail

Tap

to display the pull-down menu, and tap

Settings

- The

Settings

screen is displayed.

Figure 149: Display the pull-down menu 2.

Summary of Contents for UNIVERGE GT890










































































































































































































































































































Search results

Summary of Contents for UNIVERGE GT890

Reviews:

Related manuals for UNIVERGE GT890

Brands by name

Popular brands

NEC UNIVERGE GT890, User Manual

Search results

Summary of Contents for UNIVERGE GT890

Reviews:

Related manuals for UNIVERGE GT890

Brands by name

Popular brands