NEC Express 5800/R320c-E4 Installation Manual Download

Page: 92 / 177

3. Setting Up Windows Server 2008 R2

Express5800/R320c-E4, R320c-M4, R320d-E4, R320d-M4 Installation Guide (Windows Server 2008)

Chapter 1 Installing OS

3.14

License Authentication

Confirm whether the license has been authenticated. If it has not, perform the license authentication procedure.

The following describes the license authentication procedure.

1. Open the

Control Panel

from the

Start

menu, click

System and Security

, and then select

System

If the following message appears, Windows has already been activated on your system. You do not need
to complete this procedure.

2. If you installed from Backup DVD-ROM, replace the product key.

When the following window appears, click

Change product key

3. When the following window appears, enter the product key found on the COA label, and then click

Next

Summary of Contents for Express 5800/R320c-E4


















































































































































































Search results

Summary of Contents for Express 5800/R320c-E4

Reviews:

Related manuals for Express 5800/R320c-E4

Brands by name

Popular brands

NEC Express 5800/R320c-E4, Installation Manual

Search results

Summary of Contents for Express 5800/R320c-E4

Reviews:

Related manuals for Express 5800/R320c-E4

Brands by name

Popular brands