NEC Express 5800/R320c-E4 Installation Manual Download

Page: 69 / 177

3. Setting Up Windows Server 2008 R2

Express5800/R320c-E4, R320c-M4, R320d-E4, R320d-M4 Installation Guide (Windows Server 2008)

Chapter 1 Installing OS

Note

•

Applications available for installation are selected by default.

•

An application that has been already installed need to be uninstalled before installing it

again.

•

If your system environment does not satisfy the prerequisite for an application, you

cannot install it. (For details, refer to the on-screen information and

Chapter 2

(Installing Bundled Software.)

The selected applications are installed automatically.

5. When a message appears, click

Restart

, and then remove the EXPRESSBUILDER disk from the optical

disk drive.

Now installation of applications is completed.

3.7

Applying Service Pack

When applying Service Pack 1, refer to

"About Windows Server 2008 R2 Service Pack 1"

on the web site below.

http://www.58support.nec.co.jp/global/download/w2008r2/sp1.html

Summary of Contents for Express 5800/R320c-E4


















































































































































































Search results

Summary of Contents for Express 5800/R320c-E4

Reviews:

Related manuals for Express 5800/R320c-E4

Brands by name

Popular brands

NEC Express 5800/R320c-E4, Installation Manual

Search results

Summary of Contents for Express 5800/R320c-E4

Reviews:

Related manuals for Express 5800/R320c-E4

Brands by name

Popular brands