NEC Express 5800/R320c-E4 Installation Manual Download

Page: 47 / 177

3. Setting Up Windows Server 2008 R2

Express5800/R320c-E4, R320c-M4, R320d-E4, R320d-M4 Installation Guide (Windows Server 2008)

Chapter 1 Installing OS

3.3

Setup with Windows Standard Installer

This section describes how to install Windows with Windows Standard Installer.

Important

•

Setup with Windows standard Installer may erase all data in the hard disk drive

depending on the settings. Pay attention to input parameters.

Backing up user data, as needed, is recommended.

•

Although some dialog boxes and popup windows are displayed during installing

ft Server Control Software in Setup, do not operate from the keyboard and the

mouse. Installation is continued automatically.

Do not operate especially although the following dialog is displayed. When

installation is stopped with operation of a keyboard or a mouse, there is a

possibility that OS does not start normally.

Tips

•

Setup with Windows Standard Installer allows you to use a pre-specified parameter file

or save the parameters specified in setup as a parameter file on a removable media.

•

For details on creating a parameter file, see

Chapter 1

(

5. Windows OS Parameter

File)

Summary of Contents for Express 5800/R320c-E4


















































































































































































Search results

Summary of Contents for Express 5800/R320c-E4

Reviews:

Related manuals for Express 5800/R320c-E4

Brands by name

Popular brands

NEC Express 5800/R320c-E4, Installation Manual

Search results

Summary of Contents for Express 5800/R320c-E4

Reviews:

Related manuals for Express 5800/R320c-E4

Brands by name

Popular brands