NEC Express 5800/R320c-E4 Installation Manual Download Page 30

Page: 30 / 177

3. Setting Up Windows Server 2008 R2

Express5800/R320c-E4, R320c-M4, R320d-E4, R320d-M4 Installation Guide (Windows Server 2008)

Chapter 1 Installing OS

3.2.4

Setup procedure

1. Prepare for setup according to

Chapter 1 (3.1.2 Preparation)

2. Be sure to disable OS Boot Monitoring feature according to

Chapter 1 (3.1.3 Disabling OS Boot

Monitoring Feature)

Important OS Boot Monitoring feature is enabled by the shipping default. Setup process will

fail if this feature is enabled.

3. Turn the display unit power on, and then turn the server power on.
4. Start EXPRESSBUILDER according to

Chapter 1 (1.1 Starting EXPRESSBUILDER)

5. When the following message appears, select

OS installation *** default ***

The following window appears.

Summary of Contents for Express 5800/R320c-E4


















































































































































































Search results

Summary of Contents for Express 5800/R320c-E4

Reviews:

Related manuals for Express 5800/R320c-E4

Brands by name

Popular brands

NEC Express 5800/R320c-E4, Installation Manual

Search results

Summary of Contents for Express 5800/R320c-E4

Reviews:

Related manuals for Express 5800/R320c-E4

Brands by name

Popular brands