NEC Express 5800/R320c-E4 Installation Manual Download

Page: 81 / 177

3. Setting Up Windows Server 2008 R2

Express5800/R320c-E4, R320c-M4, R320d-E4, R320d-M4 Installation Guide (Windows Server 2008)

Chapter 1 Installing OS

Note

•

To perform this procedure, you need to log on as an Administrator.

•

RDR can only be set on the basic disk inserted into the built-in slot of NEC

Express5800/ft series. It cannot be set on the dynamic disk.

•

For the disk on which RDR is set, use the products with the same model number.

•

Be sure to configure the RDR settings in the same way not only when the OS is

installed but also when the disk is added to the PCI module.

•

Create partitions only after the duplication of the hard disk drives are configured.

•

Be sure to use a basic disk as the system disk. Only a data disk can be used for a

dynamic disk.

Dual disk configuration procedure differs depending on the procedure whether it is for the system disk (slot 0) or
the data disk (slot 1 to slot 7).

Tips

To configure the dual disk of the system disk, see

(2) System Disk Dual Configuration

Procedure

below.

To configure the dual disk of the data disk, see

(3) Data Disk Dual Configuration Procedure

below.

Summary of Contents for Express 5800/R320c-E4


















































































































































































Search results

Summary of Contents for Express 5800/R320c-E4

Reviews:

Related manuals for Express 5800/R320c-E4

Brands by name

Popular brands

NEC Express 5800/R320c-E4, Installation Manual

Search results

Summary of Contents for Express 5800/R320c-E4

Reviews:

Related manuals for Express 5800/R320c-E4

Brands by name

Popular brands