NEC Express 5800/R320c-E4 Installation Manual Download

Page: 174 / 177

1. Bundled Software for the Server

Express5800/R320c-E4, R320c-M4, R320d-E4, R320d-M4 Installation Guide (Windows Server 2008)

174

Chapter 2 Installing Bundled Software

Operational State

The Operational State reports the status of the last operation that was performed.

Status: Operational State

Operational State

Description

Ready

The previous operation has been completed successfully. The Active Upgrade

process is ready to enter the next upgrade state.

Busy

The current operation is still in progress. Allow time for the operation to complete.

Broken

The Active Upgrade Console could not complete the current operation. Check the

activity log for errors. You must correct the errors and click

Retry

to complete the

operation, or click

Abort

to abort the current upgrade session.

Partner State

The Partner State reports the status of the partner system. For example, while the system is in split mode, the
Active Upgrade Console is running on the Production Side, this field reports the status of the Upgrade Side of
the system.

Status: Partner State

Partner State

Description

DC On

The partner system operating system is shutdown, but the system still has standby

(housekeeping) power.

DC Off

The partner system operating system is shutdown and standby power is off.

BIOS POST

The partner system is performing a BIOS Power On Self Test (POST).

Hung: BIOS POST

The partner system hung in the BIOS POST.

OS Booting

The partner operating system is booting.

Hung: OS Booting

The partner system hung in the boot process.

OS Up

The partner operating system is up. (However, the system might not be available

for use until other system resources finish loading.)

Hung: OS Up

The partner operating system is hung.

OS Rebooting

The partner operating system is rebooting.

Hung: OS Rebooting

The partner system hung while rebooting.

OS Shutting Down

The partner operating system is shutting down.

Hung: OS Shutting Down

The partner system hung while it was shutting down.

OS Crashed

The partner operating system crashed.

OS Shut Down

The partner operating system finished shutting down, but the system is still

powered on.

Summary of Contents for Express 5800/R320c-E4


















































































































































































Search results

Summary of Contents for Express 5800/R320c-E4

Reviews:

Related manuals for Express 5800/R320c-E4

Brands by name

Popular brands

NEC Express 5800/R320c-E4, Installation Manual

Search results

Summary of Contents for Express 5800/R320c-E4

Reviews:

Related manuals for Express 5800/R320c-E4

Brands by name

Popular brands