Multicam Laser 2000 Series User Manual Download Page 70

Page: 70 / 242

Innovation. Quality. Performance. Best in Industry. Worldwide.

Menu

Menu Items help the operator handle many of the functions of the

MultiCam

Laser by providing the ability to

set feedrates and other parameters, run tests, and cut basic shapes. With the addition of some advanced features of
the

MultiCam

Laser, the operator can also adjust tools or duplicate shapes which create G-Code files quickly.

1. Press

to access the menu system.

2. Press

Jog Arrows

until the blinking the cursor is over a specific menu item. Certain menu

items will then pull up a sub-menu with more selection. Not all menu items will be applicable for some
systems.

Hot Keys

Keypad

Routers * Lasers * Plasma * WaterJets * Knife Cutters

www.MultiCam.com v. 11 10

Summary of Contents for Laser 2000 Series



















































































































































































































































Search results

Summary of Contents for Laser 2000 Series

Reviews:

Related manuals for Laser 2000 Series

Brands by name

Popular brands

Multicam Laser 2000 Series, User Manual

Search results

Summary of Contents for Laser 2000 Series

Reviews:

Related manuals for Laser 2000 Series

Brands by name

Popular brands