Multicam Laser 2000 Series User Manual Download

Page: 148 / 242

Innovation. Quality. Performance. Best in Industry. Worldwide.

Reboot

The Reboot function is used to reboot the machine without having to power down.

1. Press

to access the menu system.

2. Press

X-axis Jog Arrows

until Utility is highlighted in blue.

3. Press

Enter

to access the Utility sub-menu.

4. Press

X-axis Jog Arrows

until Reboot is highlighted in blue.

5. Press

Enter

to access the reboot process.

6. Press

Y-axis Jog Arrows

to move between Yes and No.

7. Press

Enter

to process the reboot of the machine. If No is selected, then the display will return to the

Utility sub-menu.

Utility

Routers * Lasers * Plasma * WaterJets * Knife Cutters

www.MultiCam.com v. 11 10

Summary of Contents for Laser 2000 Series



















































































































































































































































Search results

Summary of Contents for Laser 2000 Series

Reviews:

Related manuals for Laser 2000 Series

Brands by name

Popular brands

Multicam Laser 2000 Series, User Manual

Search results

Summary of Contents for Laser 2000 Series

Reviews:

Related manuals for Laser 2000 Series

Brands by name

Popular brands