Morgana DigiBook 450 Instruction Manual Download Page 17

Page: 17 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

1.9

PURPOSE

The machine is used to bind books using the following materials:

a) Signatures, or sheet of paper (printed or not) for the block book

b) Cardboard as cover of the book

within the limits specified in the data sheet, included in this manual.

1.9.1

SES

ROVIDED

SES

ROHIBITED

Any other use such as,

- Milling / Roughening of book spines already binder (adhesive

binder, stitching book, sewing book, etc.)

- Use of materials other than those specified in a) and b)

- Operations beyond the technical specifications are not to be re-

garded as intended use.

The user has the total responsibility of the damages to people or things due to an improper

use outside of their intended use.



MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands