Morgana DigiBook 450 Instruction Manual Download Page 30

Page: 30 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

8.7

ELECTRICAL CONNECTION

Electrical cable

The end of the cable is prepared according to the destination of the binder.

a) With the European standard plug with pro-

tective earth (PE) mounted on a 3 meters

length cable

b) Cable length of 3 meters with sectioned end,

with the earth conductor (PE)

It is the responsibility of the user to adjust the

connection cable in accordance with the appli-

cable legislation.

8.7.1

ROUND

ONNECTION

The Perfect Binder is equipped with an earth conductor (PE).

During the installation the customer must realize the ground connec-

tion in accordance with the applicable legislation.

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands