manualshive.com logo in svg

Morgana DigiBook 450, Instruction Manual, Page: 62 / 93

Share
Download
Morgana DigiBook 450 Instruction Manual Download Page 62

Operators Guide 

DigiBook 450 

61 

rel. 2.00-B 

So the machine will start to move the glue station and the timer for homogenization will start. If the 
delta between the set temperatures and the recorder one is more than 104 °C, the following message 
will  appear  “Wait.  Heating  in  Progress”  Until  the  timer  will  not  finish  (15  min),  it  will  not  be 
possible  to  load  the  glue  or  to  work.  When  the  number  indicated  with  “6”  will  go  to  900  the 
procedure is finished. At the end of this process the machine will be ready to start.  

The standby status will decrease the temperatures of 86°. 
If  the  machine  does  not  produce  any  book  for  more  than  30  minutes,  the  machine  automatically 
goes to standby  

To go out from stand by status, hold for at least a second whatever point on display, but not on the 
icons. 

The head for the extrusion is closed

The  temperatures  decrease  of  86°  in  order  to  protect  the  glue  from  unnecessary  prolonged

heating.

After that, you have to wait for glue station to reach the set temperature. 

When the temperature is correct, it will be possible to position the axes and proceed with book pro-

duction. 

Manual movements

 

MyBinding.com

5500 NE Moore Court 

Hillsboro, OR 97124 

Toll Free: 1-800-944-4573 

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Reviews:

No comments