manualshive.com logo in svg

Morgana DigiBook 450, Instruction Manual, Page: 64 / 93

Share
Download
Morgana DigiBook 450 Instruction Manual Download Page 64

Operators Guide 

DigiBook 450 

63 

rel. 2.00-B 

Select the nipping station or the delivery arm. 

1A-1B  With  these  buttons  you  can  move  the  front  and  rear  guide  to  support  the  cover  on  the 

nipping station. 

2 

With these buttons you can move the spine base plate. 

3 

With these buttons can adjust the height of the nipping station 

4 

With these buttons you raise or lower the nipping station, you can use it only when the 

spine base plate is out. 

5 

With these buttons you raise or lower the arm 

6 

With this button you can rotate the gripping hand 

7 

With this button you can close/open the fingers of the gripping hand 

8 

With this button you can enable the rotation of the belt. It is necessary to release a book 

not released in a proper way. 

MyBinding.com

5500 NE Moore Court 

Hillsboro, OR 97124 

Toll Free: 1-800-944-4573 

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Reviews:

No comments