Morgana DigiBook 450 Instruction Manual Download Page 11

Page: 11 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

1.5

SAFETY CLOTHING

Clothing to use during the cleaning and /or maintenance operations

Eye protection against any spray of PUR glue or high temperature cleaner

Respiratory mask suitable for the glue you are using

Protective gloves

Tight clothing, to avoid that they remain engaged with protruding parts.

Long hair must be covered or otherwise collected by using e. g. a protective screen.

Do not wear watches or jewels.

Safety clothing

The safety clothing IS NOT INCLUDED in the machine and must be pro-

cured by the machine user.

The operator should wear clothing appropriate to the situation and special-

ly during the following operations:

-Maintenance

-Replacing of the PUR glue

-Cleaning of the PUR system

a) Eye protection against any spray of PUR glue or high temperature

cleaner

b) Respiratory mask suitable for the glue you are using

c) Protective gloves for high temperature

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands