Morgana DigiBook 450 Instruction Manual Download Page 42

Page: 42 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

GLUE TANK

CLEANER TANK

Glue pressure tap

-- closed

| open

Chips aspiring tube

10.5

CHIPS ASPIRATOR

The chips aspirator is located inside the cabinet of the Perfect Binder and is electrically connected

to the binder herself. When the binder is delivered, the chips aspirator is ready, mechanically (aspi-

ration tube) and electrically connected, he switches on and off together with the Milling Station.

Front side picture: chips aspirator (see the arrow)

Aspiration tube

In the back of the Perfect Binder, connected to the

back preparation station.

Switch
It must be in “on” position (I = ON) during the
operation of the Perfect Binder.

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands