Morgana DigiBook 450 Instruction Manual Download Page 59

Page: 59 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

11.2

PARAMETERS FOR SINGLE AXES (GROUPS)

Standard symbols that you will find in the following pages.

Access to manual movement page

Axes preset

Group movement in the direction indicated by the green arrow. If you push the

green arrow, the dimension increases.

Group movement in the direction indicated by the red arrow. If you push the red

arrow, the dimension decreases.

The value in blue can be modified by the operator.

The value in green

cannot

be modified by the operator.

It is the current position of the axes.

Back to the previous window.

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands