Morgana DigiBook 450 Instruction Manual Download Page 82 | Manualshive

Page: 82 / 93

background image

Operators Guide

DigiBook 450

81

rel. 2.00-B

13

CLEANING THE MACHINE

When the machine works using PUR glue, it is imperative and essential an accurate cleaning of the

glue.

The dried glue is no more refusible.

Residue of glue during the drying process can cause blockages or an incorrect and not uniform ex-
trusion of the glue.
The glue group must be kept clean with the deposits of glue, PUR glue residues harden over time
and cause damages to the equipment.

Performing the “End of job cleaning” it is possible to save the machine turned off containing
PUR glue for 2 weeks.

CLEANING IS COMPULSORY for proper operation of the machine.

"If the machine is

switched off or unused for more than 120 minutes

it is necessary to make the

cycle of "End of job cleaning".

EVERY DAY:

END OF JOB CLEANING

EMPTY THE CHIPS ASPIRATOR

ONCE IN THE WHEEK:

CLEANING LATERAL EXTRUDER

CLEANING SPINE EXTRUDER

CLEANING DETAILS

In case of:

Some pages are not glued

Perform the SPINE EXTRUDER CLEANING

The glue on the side is not uniform

Perform the LATERAL EXTRUDER CLEAN-

ING

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

«
...
80
81
82
83
84
...
»

Summary of Contents for DigiBook 450






























































































Reviews:

No comments

Related manuals for DigiBook 450

Brand: PHC Pages: 4

Brand: Akerworks Pages: 2

BP27 ULTRA MAXX

Brand: NSS Pages: 20

Brand: Xerox Pages: 92

Brand: Singer Pages: 7

Brand: Singer Pages: 24

3100 SERIES 569U

Brand: Singer Pages: 22

Brand: Necchi Pages: 53

AquaRide 56314009

Brand: Nilfisk-Advance Pages: 32

AMS-210E Series

Brand: JUKI Pages: 243

Brand: Nobles Pages: 1

Brand: JUKI Pages: 68

Brand: Kenmore Pages: 90

Brand: National Flooring Equipent Pages: 36

Brand: Trusted Clean Pages: 8

SS-20-1500HS-TC

Brand: Trusted Clean Pages: 10

Brand: Trusted Clean Pages: 18

Brand: Triumph Adler Pages: 155

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands