Morgana DigiBook 450 Instruction Manual Download Page 39

Page: 39 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

Adjustment for flow rate of front air blows.

Buttons to lower/raise the cover feeder sur-

face.

Height adjustment for cover feeder surface.

Depth adjustment for creasing.

1= does not crease

Higher numbers increase scoring.

Lever to raise the creasers. It is possible to

insert between the tag and the knob a part

of the cover you are working on, in this

way you can crease several kinds of covers

with the same depth only replacing the part

of the cover.

Height adjustment of front air blows.

Knob to be removed in case of misfire.

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands