Morgana DigiBook 450 Instruction Manual Download Page 93

Page: 93 / 93

Operators Guide

DigiBook 450

rel. 2.00-B



Verify the presence of glue in the tank.



Verify that the glue in the tank is not cured.



Verify that the tank valve is open.



Verify the position of the internal lateral jaw: it must be 0.10 tenths back from the edge
of the clamp.



Verify the head height: if it comes out a little glue lower the head and increase the air
pressure of the glue group, if it comes out to much glue raise the head and lower the air
pressure of the glue



Verify that the glue is not deteriorate

14.7

NIPPING STATION



Press so much: lower the air pressure of the press group or the spine height.



Round spine: increase the press height.



Edge pinched: contact technical support.



Not uniform spine: contact technical support.

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands