Morgana DigiBook 450 Instruction Manual Download Page 10

Page: 10 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

1.4

THE SAFETY DURING THE USE OF THE MACHINE

1.4.1

ENERAL

The manufacturer guarantees that the contents of this manual are in specification with the proce-

dures required by the machine. The manufacturer therefore will be not responsible if the machine

will be used in a different way from what indicated in this manual.

1.4.2

AFETY

ARNINGS

Before the use of the machine, please read carefully the manual.

Save the manual for further needs.

By apply different procedures, and not the specific procedures described in the manual, can produce

operational problems.

Please, read carefully the following safety rules.

It is forbidden to use the machine when occurs one of the following situations:



in explosive environment;



in flammable atmosphere;



in excessive durst environments.

Danger!

Failure to comply with some or all the instructions listed in this manual could

cause damage to the machine and / or personal injury. The manufacturer is not re-

sponsible for an arbitrary and improper use of the machine such as:

Using the machine by untrained personnel;

Use contrary to law;

Incorrect installation;

Defects in electrical power and / or pneumatic;

Partial or total failure to comply with the instructions;

Lack of maintenance and / or use of aftermarket parts;

Changes or other actions not authorized by the Manufacturer;



MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands