Morgana DigiBook 450 Instruction Manual Download Page 41

Page: 41 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

STACKER EXIT BELT

Frontal blowing system. It is magnetic,

with possibility to adjust position and

quantity of the air dispensed through the

built-in valve. Support with depth adjust-

ment.

Lateral hedge, magnetic, with support

function.

Automatic system to adjust height and

manual system to adjust depth

Automatic system to adjust height, this is

regulated by a lateral sensor.

Once you have filled the stacker, the ma-

chine send an alarm to the A62 (

Books

Stacker Full

To rise again the plane, wave fast your
hand in front of the sensor “A”

On the back

Gate access to the tanks.

The machine makes movements only with the

door closed.

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands